Thursday, March 3, 2011

agamemnon counterpart

15 comments:

  1. MY BRAIN IS FULL OF FUCK

    ReplyDelete
  2. SO IS MINE! I still don't understand why this video creeps me the fuck out, it just does.

    ReplyDelete
  3. I don't know what to think

    ReplyDelete
  4. sounds like somebody having an orgy

    ReplyDelete
  5. It's rumored to be the sound of a Japanese school student being killed.

    ReplyDelete
  6. this was actually kinda creepy... especially since its nightmare retardant

    ReplyDelete
  7. Well, I see this is what you get when you make a cartoon while on LSD.

    ReplyDelete
  8. giygas: the kids show

    ReplyDelete
  9. I.CAN'T.STOP.WATCHING...

    ReplyDelete
  10. I would watch but the slide it shows before you watch is........demented almost like........me.....

    ReplyDelete
  11. Remove the valve cap and fully deflate the tube bycarbon bike rimsdepressing the valve stem with the hooked end of your tire lever. There are two main types of valve stems, a schrader valve and a presta valve. This tutorial is based on a schrader valve, but I will be covering the different valve types in another tutorial.
    Now it’s time to remove your tire, one side at a time. Choose a section of tire that is away from the valve and hook one of the tire levers under the bead, directly in line with one of your spokes. Pry one side of the tire bead over the edge of the rim, and then hook the end of the tire lever to the nearest spoke. Insert another tire lever two spokes away from the first, and a third another two spokes away. Now the middle lever should fall out, and you can continue the process. When the tire is loose enough you can just run a tire lever around the rest of the rim to pull the whole side over.
    After you have removed one side of carbon fiber rimsthe tire, the other side should come off very easily.
    Inspect Tube
    Now remove the tube from the tire, and try to keepcarbon bicycle rimstrack of where it was positioned in relation to the tire. Inflate the tube to approximately twice its original size. This will expand the hole making it easier to find.
    Listen carefully to the entire circumferenceof the tube; you should hear a hissing sound that will indicate where ICAbike01 the leak is. As a last resort you can submerge the tube in water and watch for bubbles, but you’ll want to avoid doing this as you’ll need the tube to be completely dry in order for the patch glue to work.
    Once you’ve found the leak, take note of whether it is on the inner or outer side of the tube.
    If the hole was on the outer side of the tube, inspect the inner surface of the tire in that spot to make sure the object that caused the puncture is not still stuck in the tire. Double check the entire inner side of the tire by running your fingers along the entire surface, feeling for obstacles along the way.
    If the hole was on the inner side of the tube,inspect yourzipp 404entire rim to make sure there are no sharp burrs in the metal, and that the rim tape is properly protecting the tube from your spoke ends.
    Now that the rim and tire are clear, it’s time to patch the tube. Select an appropriate sized patch for the hole. Use the sandpaper or scraper provided in your kit to buff the surface of the tube for an area a bit larger than the patch. You need to buff the tube so that it is no longer shiny. If the molding line is running along the area where the patch is to be applied, you must sand it down completely, or it will provide an air channel. Once buffed, avoid touching that area with your fingers.
    Apply a dab of rubber cement, and then spread it into a thin coat, using your cleanest finger. Work quickly. You want a thin, smooth coat of cement; if you keep fiddling with it as it begins to dry, you’ll risk making it lumpy. The thinner the cement, the faster it will dry. It is very important to allow the cement to dry completely.
    Peel the foil from the patch and press the patch onto the tube firmly, squeezing the patch tightly onto the tube.

    ReplyDelete
  12. What does the a and o supposed to stand for

    ReplyDelete